{"product_id":"silikonine-hidroizoliacija-topbase-st-fiber","title":"TopBase ST Fiber – Silicone Waterproofing Coating with Glass Fibre, Grey\/White, 1-4.7 kg","description":"\u003ch3\u003eChimney, joint or detail leaking again, where a thinner coating would just run off?\u003c\/h3\u003e\n\u003cp\u003ePandaCoat TopBase ST Fiber is the glass-fibre reinforced version of TopBase ST, built for vertical surfaces and detail work: chimneys, gutters, joints, sloped upstands. The glass fibre thickens the silicone into a non-drip paste, so the coating stays put on vertical surfaces instead of sliding down.\u003c\/p\u003e\n\u003ch3\u003eTopBase ST Fiber benefits\u003c\/h3\u003e\n\u003cp\u003e🧱 \u003cstrong\u003eNon-drip consistency for verticals and details\u003c\/strong\u003e\u003cbr\u003eGlass fibre thickens the silicone – it clings to chimneys, upstands and joints without running, even when applied vertically.\u003c\/p\u003e\n\u003cp\u003e🔧 \u003cstrong\u003eBetter crack bridging\u003c\/strong\u003e\u003cbr\u003eThe thicker consistency reliably seals small details and cracks where a thinner coating would be too weak.\u003c\/p\u003e\n\u003cp\u003e🌦️ \u003cstrong\u003eWeatherproof in any conditions\u003c\/strong\u003e\u003cbr\u003eOnce cured, the membrane resists UV rays, rain, snow and temperature swings from -30°C to +80°C.\u003c\/p\u003e\n\u003cp\u003e🖌️ \u003cstrong\u003eEasy to apply – usually no primer needed\u003c\/strong\u003e\u003cbr\u003eApply with a brush or roller in 2-3 thin coats. Primer is usually not needed on ceramic or metal; for concrete use Primer VL, for bitumen Primer VL 2K.\u003c\/p\u003e\n\u003ch3\u003eWhat it is\u003c\/h3\u003e\n\u003cp\u003eA single-component, glass-fibre reinforced silicone coating – the same TopBase ST chemistry, just thicker and non-drip. Cures with atmospheric humidity into a strong, elastic, waterproof membrane. Used as a TopBase ST complement for detail elements, or standalone on smaller\/vertical areas. Available in grey or white.\u003c\/p\u003e\n\u003ch3\u003eWhere to use\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eChimneys, gutters, roof joints and upstands\u003c\/li\u003e\n\u003cli\u003eSloped and vertical surfaces where a thinner coating would run off\u003c\/li\u003e\n\u003cli\u003eSmall cracks and damaged spots\u003c\/li\u003e\n\u003cli\u003eCaravan and motorhome roofs, outbuildings, terraces\u003c\/li\u003e\n\u003cli\u003eConcrete, metal, ceramic, wood and glass surfaces\u003c\/li\u003e\n\u003cli\u003eExtra reinforcement alongside TopBase ST on flat-roof details\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eTechnical properties\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eRelative density: 1.265 g\/cm³ (SDS)\u003c\/li\u003e\n\u003cli\u003eDynamic viscosity: 1800-2200 cP\u003c\/li\u003e\n\u003cli\u003eFlash point: 67°C\u003c\/li\u003e\n\u003cli\u003eWorking temperature: -30°C to +80°C (same TopBase ST chemistry)\u003c\/li\u003e\n\u003cli\u003eVOC (Supply): 21.93% by mass (0.28 g\/L, 20°C)\u003c\/li\u003e\n\u003cli\u003eClassification per CLP 1272\/2008: not hazardous (EUH066, EUH208 supplementary statements)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cem\u003eSource: PandaCoat TOPBASE ST FIBER Safety Data Sheet (SDS, v.30). This version has no separate technical data sheet (TDS) or Declaration of Performance (DoP\/ESD) – only the base TopBase ST line has those.\u003c\/em\u003e\u003c\/p\u003e\n\u003ch3\u003eApplication\u003c\/h3\u003e\n\u003cp\u003eThe substrate must be clean, dry, free of dust and grease (concrete moisture \u0026lt;5%). Primer is usually not needed on ceramic or metal; for concrete use Primer VL, for bitumen Primer VL 2K. Pre-seal joints and seams with TopBase ST Paste sealant.\u003c\/p\u003e\n\u003cp\u003eApply TopBase ST Fiber with a brush or roller in \u003cstrong\u003e2-3 thin coats\u003c\/strong\u003e (unlike base TopBase ST, which only needs one thick coat) – the thicker consistency simply doesn't allow a single thick coat to be applied on vertical surfaces. Allow 3-48 hours between coats, depending on ambient conditions. A surface skin forms after ~2 hours.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eNote:\u003c\/strong\u003e this is a complementary TopBase ST version for details\/verticals – use it standalone on small areas, or together with base TopBase ST on flat-roof details, not as a replacement for a full roof.\u003c\/p\u003e","brand":"PandaCoat","offers":[{"title":"White \/ 1 kg","offer_id":60836935139662,"sku":"HDR-AMZ-ST-FIBER-1WT","price":20.65,"currency_code":"EUR","in_stock":false},{"title":"Grey \/ 4.7 kg","offer_id":60836935172430,"sku":"HDR-AMZ-TOPBASE-ST-FIBER-1GAL-SF-GR","price":59.0,"currency_code":"EUR","in_stock":false},{"title":"Grey \/ 1 kg","offer_id":60836961878350,"sku":"HDR-AMZ-ST-FIBER-1GR","price":12.66,"currency_code":"EUR","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0825\/5714\/1326\/files\/01-pandacoat-topbase-st-fiber-grey-1kg-main-image.jpg?v=1789561356","url":"https:\/\/pandacoat.de\/en\/products\/silicone-waterproofing-topbase-st-fiber","provider":"Pandacoat","version":"1.0","type":"link"}